- 4-ports RS-422/485 with isolation to redundant Ethernet
- Supports 2KV isolation protection
- RTTD, Redundant to the Device function Dual Ethernet ports, network auto-recovery in Less Than 200ms
- Four Digital Inputs and Two Digital Outputs
- Redundant Power Inputs by 12-48VDC Terminal Block and DC Jack
- Independent serial services, Virtual COM, TCP Server/Client/Tunnel and UDP Connections
- JetPort Commander, Easy-to-use Windows Utility with smart setup Wizards.
- Secured Management by HTTPS and SSH
- Event Notification by Syslog, Email, SNMP trap and Digital Output
- Vertical mounting by DIN Rail, Wall mount/Desk-top
JetPort 5604i series is a 4-port Isolation Redundant Serial Device Server. Users can use one IP address, Redundant Ethernet paths (RTTD Technology) to control maximum of 4 serial devices over the Ethernet. To configure JetPort Commander, the easy- to- use utility for Windows or choose HTTPS/SSH for secured management. JetPort 5604i series are also equipped with two types of power inputs, four 5V TTL Digital Inputs and two Digital Outputs. JetPort 5604i especially provides 2KV isolation protection for the critical industrial environments. These are value-added feature for user to construct the field installation.
World's First RTTD Technology
RTTD, Redundant to the Device JetPort 5604 series provide dual Ethernet ports. When the dual Ethernet ports are connected, only one path will be activated, this is known as Primary path. The un-activated path will be the Backup path. When the primary path is down, the backup path will recover Ethernet connection in less than 200ms.
Inter-connect RTTD with Super Ring
JetPort 5604 RTTD technology works well with JetNet 4000/5000 series Super Ring technology, which provides users complete redundant solution from network infrastructure to the serial devices.
Four Serial Interfaces Can Be Configured for Different Mode
JetPort 5604 series have four serial interfaces, and all of the interfaces can be configured with different serial interface types, such as RS232, RS422, 2-wire RS485 or 4-wire RS485. Each of the ports also can be configured with different service modes. You can configure serial port 1 to Virtual COM mode, serial port 2 to TCP server, serial port 3 to TCP client and serial port 4 to UDP mode. All of the serial ports have their own settings and can work well at the same time.
Up to 5 Simultaneous Connections
To JetPort series provide you up to 5 simultaneous Virtual COM, TCP Server, TCP Client, TCP Tunnel and UDP connections. All the services are developed over the TCP/IP protocol stacks. You can easily connect to the serial devices over Ethernet and plan your serial to Ethernet applications.
Windows Virtual COM
After installing JetPort Windows driver, the serial port on the JetPort can be accessed by the Windows as the virtual COM port. Users do not have to modify the existing program to upgrade the legacy serial communications into serial over IP application.
You can also use TCP/UDP socket programs to control JetPort's serial port. JetPort can be configured as TCP Server, to listen to TCP connection request, or as TCP Client, to actively request TCP connection to send data, or as UDP mode for multiple destination transmission.
5V/TTL Digital Input and Digital Output
JetPort 5604 series provide four digital inputs and two digital outputs. It allows users to connect the termination units' 5V TTL digital input/output. JetPort Commander allows you to monitor the status of the DI and DO, and assign the value of 0 or 1 to DO. JetPort also provides one data port for user to program DI/O "get" and "set" commands figure on the right. The logic Low (Value=0) power voltage is 0-0.8V, 0.8V is the max value. The logic High (Value =1) power voltage is 2-5V, 2V is the min value. JetPort also opens one TCP socket port for DI/DO programming commands.
Easy-to-Use Windows Utility and Smart Wizards
Korenix JetPort Commander is known for its abundant features, user-friendly interface and smart setup wizards. Customer can browse the JetPorts, configure services, monitor devices and group setup.
The group setup wizard includes Virtual COM Wizard, Group Setup Wizard, Group Firmware Wizard, Serial Tunnel Wizard and Group IP Wizard.
Virtual COM Wizard: Three steps to configure all Virtual Com ports
Group Setup Wizard: Copy specific configurations from one to other devices
Group Firmware Wizard: Group update firmware to multiple device(s)
Serial Tunnel Wizard: Couple devices to serial tunnels
Group IP Wizard: Configure IP to multiple device(s)
2* 10/100BaseTX, Redundant Dual Ethernet
|Auto Recovery in less than 200ms|
Built-in 1.5 KV magnetic isolation protection
IP, TCP, UDP, ICMP, DHCP, BootP, ARP/RARP, SNMP, HTTPS, SSH, SNTP, SMTP
XON/XOFF, RTS/CTS, DTR/DSR
|Long Distance Termination|
2*pin 120ohm DIP switches
|Port to Port, Port to Power/GND/Case|
Logic 0: 0.8V max (0-0.8V)
Logic 1: 2.0V min (2-5V)
Logic 0: 0.8V max (0-0.8V)
Logic 1: 2.0V min (2-5V)
Power 1/Power 2: Startup(Red); Ready(Green)
Left:100M Link (Green On)/Activity(Green Blinking)
Right:10M Link (Orange On)/Activity(Orange Blinking)
Serial 1/2/3/4:TX only(Green), RX only(Red), Both RX/TX(Orange)
|Windows Utility-JetPort Commander, HTTP, Telnet|
|Virtual COM, TCP Server, TCP Client, TCP Tunnel and UDP|
|Software reload default, Hardware reset button|
|Embedded beeper for positioning|
|Redundant to the Device, Auto-recover in less than 200ms|
|16 IP addresses to prevent illegal users|
|Devices¡¦ status, VCOM status|
|RFC1213 MIB II, RFC1317 RS232_like and SNMP Trap|
|Automatic e-mail warning by pre-defined events|
|Trap to Syslog server or local display|
|Cold/Warm Start, Login Failed, IP and Password Changed, Access IP Blocked, DI/DO changed, Serial Port DCD/RI/DSR/CTS changed, Serial Port connected/disconnected|
Device Discovery, Auto IP, Network Setting, Device and Serial Port Setting and monitoring, Notification setting, Firmware Upgrade, Configuration Backup and Restore, Group Configuration Wizards
Virtual COM, TCP Server, TCP Client, TCP Tunnel and UDP
TCP Alive Check Timeout, Inactivity Idle Timeout, Performance mode, Delimiter, Force TX Timeout for Data Packing and Force TX interval time
|Group Configuration Wizard|
JetPort Commander: Group IP Wizard, Group firmware upgrade, Group Backup/Restore, VCOM and TCP Tunnel Setup Wizard
PWR1: 12~48VDC Terminal Block
PWR2: 12~48VDC Power Jack with Power Adapter
1 KV Burst (EFT), EN61000-4-4
0.5 KV Surge, EN61000-4-5
FCC Class A, CE Class A , UL, RoHS
5% to 95% (Non-condensing)