Motium MLC-810 Rugged LCD-näyttö: 8" aurinkoluettava kosketusnäyttö 800x600, taustavalaistu, IP65/NEMA4 suojattu, -20°C ... +65°C, erikois-liitäntäkaapeli mukana, VESA-asennus, 9-34V DC

Tuff View MLC-810 Rugged, Sunlight Readable 20cm (8.0-inch) LCD Monitor

• 800x600 native resolution.
• High quality image with wide viewing angle.
• Truly sunlight readable (with touch screen).
• Real backlight control (no night-blindness).
• Completely water and dust proof (IP65/NEMA4).
• 5-wire resistive touch screen with USB and RS232.
• -20°C to +65°C operating temperature range.
• Designed for continuous vibration environments.
• Rugged, automotive grade connector.
• Wide input voltage range with transient protection.
• Standard 75mm VESA mount.
• Low power consumption. 8W max at full brightness.

Motium's Tuff View 8-inch LCD monitors have been designed for rugged environments such as industrial control and the transportation industry, be it in-vehicle for automotive (cars, busses, trucks), marine or aircraft. Each aspect of the design considered the unique needs of these markets.

Image quality is brilliant, with very wide viewing angle and 800x600 native resolution. The monitor is truly sunlight readable (with touch-screen fitted), and has real backlight control*, removing any night-blindness issues.

The MLC-810 is water and dust proof (to IP65/NEMA-4), and has been designed for operation in continuous vibration environments, and to cope with shock.

A 75mm VESA mount allows industry standard in-vehicle mounting hardware to be used.

The touch screen interface supports both USB and RS232 (allowing operation with long cable runs). An internal speaker allows PC audio and warning tones to be easily heard.

The MLC-810 operates from 9V to 34V DC and has a load-dump and transient protected power input, allowing direct connection to vehicle power. Typical operating power is less than 8 watts, extremely low for a monitor with this performance.

An operating temperature range of -20°C to +65°C allows the MLC-810 to be used in a wide variety of conditions.

* On standard LCD monitors, when the brightness is adjusted, what actually happens is the colours are changed, but the light level leaving the monitor is the same. The MLC-810 changes the actual backlight light level and leaves the colours the same. (An optional automatic backlight brightness control, using an in-built light sensor is available.)

Key Markets

• Transportation: automotive in-vehicle display.
• Cars.
• Trucks.
• Mining equipment.
• Buses.
• Marine.
• Trains.
• Aircraft.
• Industrial automation

Display Characteristics
Viewable area	4:3 aspect ratio.   162mm wide x 121.5mm high. 20.32cm (8.0-inch) diagonal.
Native Resolution	800 x 600.   Dot pitch: 0.2055mm x 0.2055mm.
Contrast ratio	500:1 typical.   400:1 minimum.
Colours	18-bit  (262,144).
Response time	Ton: 10ms typ.   Toff: 15ms typ.
Brightness	700 nits typical. This value only applies to indoor performance. The effective outdoor performance is greater than 1,000 nits. (1 nit = 1 Cd/m2.)
Viewing angle	Horizontal:   140° typ, 120° minimum. Vertical:   Up: 50° typ and 40° minimum.   Down: 70° typ and 60° minimum.
LCD Controller
Video input interface	VGA: Analog RGB, 0.7Vp-p. (DVI is available for OEM orders.)
Input resolutions	640x480, 800x600, 1,024x768.   The monitor automatically scales the input signal.
Input vertical frequency	60Hz and 70Hz.   60Hz is recommended.
Configuration	On-Screen Display (OSD) includes: Contrast Ratio, Brightness, H-position, V-position, Clock Phase and Colour Balance.
User interface
Monitor controls	Front panel buttons are:   Power On/Off, Backlight Brightness Up and Down, OSD Menu.
OSD (On Screen Display) menu controls	OSD menu control buttons are:   Menu / Select, Left and Right.
Audio
Speaker	Front panel mounted speaker, with internal fixed-gain amplifier. The speaker is intended for connection to a PC, for operator feedback and warning tones. This is a good quality speaker, not a low-cost piezo.
Microphone	Front panel mounted microphone, with internal pre-amplifier. (This is an OEM option, and is not fitted as standard.) The microphone is intended to connect to a PC, for audio recording or use in emergencies.
Touch Screen
Touch type	5-wire resistive.
Glass thickness	1.8mm.
Operation force	< 1N with a stylus of 0.8mm radius.
Linearity	< 1.5% for both X-axis and Y-axis.
Contact bounce	< 10ms.
Impact	No damage with a 9g steel ball dropped into the centre of the panel from a height of 30cm. Static Load: 5kg load over a 10mm area for 10 seconds.
Hardness	3H pencil pressure 1N @ 45 degrees.
Durability write test	10,000,000 times, with a force of 250g and a silicon rubber stylus of 0.8mm radius.
Durability knock test	1,000,000 times, with a force of 250g, 3Hz R8/HS60.
Touch Screen controller
Resolution	2,048 x 2,048.
Report rate	250 points/second maximum with USB interface. 160 points/second maximum with RS232 interface.
Response time	20ms.
Accuracy tolerance	Maximum +/-0.5% tolerance.
Interface	USB1.1 or RS232 (EIA/TIA-232-F compatible). Both interfaces are transient protected.
Data rate	RS-232 Data rate is 9,600 bps 8N1.
Touch Screen driver software
Calibration	Fast 4-point position.
Compensation	Accuracy: 9-point and 25-point linearity position. Edge compensation.
Draw test	Position and linearity verification.
Controller setting	Supports multiple controllers. Dynamic add/remove controllers. Change controller interface without reboot.
Languages	Supports 10 languages for Windows.
Mouse emulator	Right and left button emulation. Click/drawing mode.
Sound notification	No sound.   Sound on touch contact.   Sound on touch release.
Double click	Configurable double click speed.   Configurable double click area.
OS support	Windows 2000, XP, Vista and Windows 7. Windows Embedded. Windows CE.NET (4.x, 5.0). CE 6.0. Linux (up to Kernel 2.6.x), 32-bit and 64-bit. MS-DOS: supports display resolution: 320x200, 640x200, 640x350, 640x480, 800x600, 1,024x768 and 1,280x1,024. Mac OS 9.x and OS X (Power PC, Intel CPU). QNX Neutrino RTOS V6.3.
COM Port support	Supports COM1 to COM256 for Windows and Linux, and COM1 to COM8 for DOS.
Display support	Supports monitor/display rotation.   Supports multiple monitors.   Supports split monitor.
Physical Characteristics
Dimensions	215mm Wide x 183mm High x 37mm Deep (plus 18mm for connector body;   plus 54mm when connector is mated).
Weight	1.0kg.
Shipping	Shipping dimensions: 260mm Wide x 210mm High x 85mm Deep. Shipping weight: 1.25kg.
Ambient Temperature	Operating: -20°C to +65°C. Storage: -20°C to +80°C.
Humidity	10% to 90% RH, non condensing.
Certification	C-tick.   Other certifications available upon request.
Power
Power supply	Input voltage range 9VDC to 34VDC.
Power consumption	8W maximum.
Digital input	The monitor has a digital input for power on and off control. This input is different to the Power On/Off button. Using this input results in zero off-state power consumption.
Transient protection	Load dump and other transients specified in ISO-7367.