|VSCOM announces the new product line of Modbus Gateways named ModGate. These convert the Modbus protocol from network to serial lines. There will be models providing 1 through 8 serial ports controlled via Ethernet. Also available will be devices with an additional Wireless LAN as of 802.11b/g protocols. |
The Modbus protocol has been invented in the late 70s to communicate with PLC devices. The connection has been established by simple serial links, based on RS232. Today implementations also allow RS485 as physical layer to avoid distance limitations and use multiple devices connected to one serial line simultaneously. The primary Modbus/ASCII transmission mode got the Modbus/RTU as companion, which enhances the data throughput by transmitting the data in direct binary form. Later Modbus got implementations on TCP, to transfer commands and data over networks.
* ModGate operation modes
VScom ModGate devices connect Modbus on TCP with Modbus on serial lines. They map a target address to a physical connection.
The so-called 'Promiscuous Mode' is the most simple configuration. All Modbus messages received from a TCP host are sent to the serial port, and all messages from the serial port are sent to the TCP host. This connects one serial port with one defined TCP host.
'Mapping Mode' provides use of more flexible configurations. The user defines a list of Modbus addresses assigned to a certain serial port or a TCP host. This list is the mapping table. By inspection of the address field in a received message the ModGate decides which port to sent this message to.
ModGate devices with multiple serial ports have independent configurations for the ports. The serial parameters on one port may differ from those of the other ports. First users configure the flavour Modbus/ASCII or RTU to use on the serial line. Then they define the usual parameters as bitrate, parity, stop and data bits.
Also the physical configuration as RS232 or RS485 is defined by the configuration software. There is no need to open the case or set the DIP switches for decisions like that.
* Modbus Routing
The mapping table specifies target Modbus lines a received message will be sent to. Messages received from a serial port typically have a target defined as a TCP host. If the connection is not already established when the message arrives, ModGate contacts the host. Such a host can be another ModGate, which will forward the message to one of his serial ports. This function allows to connect several serial Modbus lines in different locations.
On a ModGate with multiple serial ports the target may be another serial port. The ModGate will then forward messages between those serial ports. Since the serial parameters may differ from each other, ModGate will act as a protocol translator. For example one RS485 line using Modbus/RTU at 115200bps can connect to a RS232 line with Modbus/ASCII at 9600bps.
Most network functions in ModGate devices are based on TCP. The protocol Modbus/TCP is defined to use TCP. The configuration software is available via HTTP, i.e. in the web browser. This also uses TCP to make the connection. TCP/IP is the base protocol suite which makes the Internet work. As the consequence Modbus devices not only operate in Intranets, they also work via the Internet. Customers install and configure the Routers to connect the ModGate devices to the Internet.
For configuration users need to know the IP address used by the ModGate. The ModGate use UPnP functions to announce their presence in a LAN. So on Windows they appear in the Network Places, where it is simple to connect the browser to the ModGate. UPnP uses Multicast protocol formats, these are typically blocked by Routers.
Ethernet is the primary network type available in all ModGate devices, which connects to the LAN. If the LAN is connected to Internet, ModGate is available worldwide. The models providing additional WLAN (802.11b/g) use a second way connecting to Intranet/Internet, ModGate can operate both interfaces at the same time. With WLAN they support mobile operation.
- Controls 1 Modbus line located virtually anywhere via Ethernet or Internet
- LAN interface 10BaseT/100BaseTx Ethernet
- Configuration over WEB Browser
- Supports TCP/IP, DHCP, ICMP, HTTP, DNS
- Supports ART (Automatic Receive Transmit control)
- RS232/485 interface selectable by Software
ARM 9 166 MHz
16C950 or compatible
16MB SDRAM, 2 MB Flash
RJ45 for Ethernet,
DSUB 9 male for serial Port
TCP/IP, DHCP, ICMP, HTTP, DNS
RS232/485 selected by software
No. of port
1, Speed up to 115200 bps
RS232 full duplex
RS485 2 wire, half duplex, with echo
RS232: TxD,RxD, RTS,CTS, DTR,DSR, DCD, RI, GND
RS485: 2 wire Data+/-, GND
RS485 Data control
Controlled by ART (Automatic Receive Transmit control)
Up to 115200 bps
None, even, odd
Modbus RTU or Modbus ASCII protocol selected for each serial port individually
Direct mapping of Modbus addresses to serial ports or TCP connections
Mapping of serial ports to TCP connections
|Power and Environment|
9 - 30V DC, 500mA @ 12V
Power supply Adapter
12V DC, 1A. Connected by Terminal block
73 x 115 x 27 mm (W×L×H)
101 x 121 x 27 mm with DB9 connector & DIN rail mounting kit
0°C - 55 °C
-20°C - 85°C
SECC sheet metal (1mm)
Dip switches set a defined temporary IP Address to contact via WEB Browser
Promiscous Mode :
Messages received from the network are sent to the serial port, messages from the serial port are sent to the connected network host.
Mapped Mode :
Received messages are scanned for their target address. This address is found in a table, the message is sent to the defined connection (serial or TCP).
Configuration over WEB Browser
Automatic Receive Transmit control for RS485
Domain Name Server support
Serial Interface configurable by software
Firmware update over WEB Browser
LEDs for Power, serial Tx, Rx, Ethernet Link, Speed
Webinterface is password protected. The password can be changed in the Webinterface.
FCC Class A, CE Class A
. ModGate 113
. Power supply adapter 12V, 1000mA
. CD-ROM with user manual
. DK-35A DIN-Rail mounting kit